Compost Heater

Compost Bioreactor Design

Grades:
7-12
Unit:
Bioreactor Water Heating
Lesson Number:
2
Description:

Solar energy is available when the sun shines but energy can be supplemented at night by the release of energy during the composting of organic waste. In this activity, we will experiment with the feasibility of harnessing thermal energy to heat water with...

Energy Content:
Biomass Energy,
Thermal Energy (Heat)
+
-
More Details Less Details
Learning Goal(s):
1. Students will research the science of composting and proper maintenance methods to build their own bioreactor. 2. Students will research the proper composition of compost for maximum heat production. 3. Students will transfer the thermal energy in compost to a container of water heat water with by placing a vessel in the middle of the active compost/bioreactor.
Pedagogy & Practice:
Engineering Design,
Group Work/Collaboration,
Hands-on Materials
NGSS Science and Engineering Practices:
3: Planning and Carrying Out Investigations,
4: Analyzing and Interpreting Data,
6: Constructing Explanations and Designing Solutions
Author:
Tami Church
Relevant NGSS PE:
MS-PS3-3,
MS-PS3-4,
MS-PS3-5,
HS-PS3-3
Other Subjects Covered:
ELA: Vocabulary Development,
Math: Measurement
Estimated Activity Length:
2 hours
Simple Circuit

Introduction to Circuits

Grades:
7-8
Unit:
Solar vs. Wind Energy
Lesson Number:
2
Description:

This lesson begins with students having hands-on experiences creating electrical circuits using a battery, wires, and a light bulb. Students will learn that electricity is the flow of electrons, and how electricity moves within a circuit.

Energy Content:
Circuitry,
Electrical Energy,
Electrons
+
-
More Details Less Details
Learning Goal(s):
By the end of these two lessons students should be able to: 1. Create a simple circuit on their own when given the appropriate materials. 2. Diagram the flow of electrons within a circuit. 3. Differentiate between series and parallel circuits.
Pedagogy & Practice:
Hands-on Materials
NGSS Science and Engineering Practices:
2: Developing and Using Models
Author:
Craig Marais
Relevant NGSS PE:
MS-PS3-5
Other Subjects Covered:
ELA: Speaking & Listening,
ELA: Vocabulary Development
Estimated Activity Length:
0 sec
Wave Attenuator

Testing a Tidal Wave Attenuator

Grades:
6-12
Unit:
Wave Attenuator
Lesson Number:
3
Description:

Students will test the efficiency of the tidal wave attenuator models that they previously built. They will determine variables on their models they can manipulate, such as wire gauge and magnet strength, and measure the effects of manipulating this...

Energy Content:
Wave Energy
+
-
More Details Less Details
Learning Goal(s):
1. Students will investigate variables that may affect the output of an energy conversion device (wave attenuator). 2. Students will interpret data to identify which variables increase electrical output for these model wave attenuators. 3. Students will communicate results from scientific inquiry to identify factors that are important to optimizing the design of a wave attenuator.
Pedagogy & Practice:
Engineering Design,
Establishing a Culture of Science,
Group Work/Collaboration,
Hands-on Materials,
Project-Based Learning
NGSS Science and Engineering Practices:
1: Asking Questions and Defining Problems,
3: Planning and Carrying Out Investigations,
4: Analyzing and Interpreting Data,
6: Constructing Explanations and Designing Solutions,
7: Engaging in Argument from Evidence
Author:
Tabatha Roderick
Relevant NGSS PE:
MS-ESS3-3,
MS-ETS1-1,
MS-ETS1-4,
MS-PS2-4,
MS-PS3-5
Other Subjects Covered:
ELA: Speaking & Listening,
ELA: Writing,
Math: Measurement
Estimated Activity Length:
5 hours

Pages